← Guides

Silica safety in countertop fabrication: OSHA's standard in plain words

Short answer: cutting, grinding and polishing stone can put respirable crystalline silica in the air, and breathing it can cause silicosis, which has no cure. OSHA's limit is 50 µg/m³ averaged over an 8-hour day, with an action level of 25 µg/m³. Employers must assess exposures, use dust controls, provide respirators when controls aren't enough, keep a written exposure control plan, and offer medical exams and training. OSHA and NIOSH say the hazard "can be mitigated in most countertop operations" with dust control methods that follow the standard.

This is a plain-language summary of OSHA's and NIOSH's own pages, checked on 2026-11-05. It isn't legal, medical or compliance advice, and we aren't safety professionals. The standards themselves are what count, so follow the links.

The two documents to read first

Who's exposed

The alert says the exposure "exists in fabrication shops and during on-site finishing/installation." Workers using powered hand tools such as saws, grinders and high-speed polishers "have some of the highest RCS exposures" in the industry. RCS is respirable crystalline silica. Workers doing other tasks close to dusty operations may also be exposed (alert).

What it does to people

OSHA says that breathing crystalline silica dust "can cause silicosis, which in severe cases can be disabling, or even fatal," and that "there is no cure for silicosis." It also lists lung cancer, chronic obstructive pulmonary disease (COPD) and kidney disease (OSHA health effects).

OSHA says silicosis typically occurs after 15 to 20 years of exposure, but also that very high concentrations can, in rare instances, bring on symptoms "within weeks instead of years." OSHA's hazard analysis describes a study of 52 engineered stone workers diagnosed with silicosis, with a median age of 45 (analysis).

How much silica is in the stone

These are the typical figures from the alert, which notes that content "will vary among stone varieties":

Stone Typical crystalline silica content
Engineered stone under 0.2% to 95%
Quartzite 95% or more
Quartzitic sandstone 90% or more
Sandstone 60% or more
Slate 20 to 40%
Granite 10 to 50%
Marble and limestone under 5%
Soapstone varies

So this isn't only an engineered stone issue, and lower-silica stone can still produce a measurable exposure. In one OSHA example, two finishers dry grinding a very low-silica marble with no engineering controls were at 39 and 45 µg/m³, above the action level. The alert says to check content in the "safety data sheets for the products."

The numbers

Level What it triggers, in OSHA's words
Action level 25 µg/m³, 8-hour average "Assess employee exposures to silica if it may be at or above" this level
Permissible exposure limit (PEL) 50 µg/m³, 8-hour average "Use dust controls to protect workers from silica exposures above the PEL"

µg/m³ means micrograms of silica per cubic meter of air (OSHA general industry page).

Which standard applies

OSHA has two silica standards, and the alert names both for this trade:

Some requirements differ between them, and one point is worth reading closely. The construction standard has a Table 1 of tasks and control methods. OSHA's FAQ says a general industry employer can follow the construction standard instead only "if the task performed is indistinguishable from a construction task listed on Table 1" and "the task will not be performed regularly in the same environment and conditions" (OSHA FAQ).

OSHA's hazard analysis describes an inspection of a marble and granite company that was using the construction table for wet cutting in its shop. OSHA issued citations, including for failing to conduct silica exposure monitoring.

State Plans: OSHA notes that State Plans "may have different or more stringent requirements" (OSHA). If your state runs its own plan, check its rules as well.

What the general industry standard requires

OSHA's own summary of the general industry standard says that, among other things, employers must:

  • assess exposures that may be at or above the action level
  • protect workers from exposures above the PEL
  • limit access to areas where workers could be exposed above the PEL
  • use dust controls to protect workers from exposures above the PEL
  • provide respirators when dust controls can't limit exposures to the PEL
  • use housekeeping methods that don't create airborne dust, if feasible
  • establish and implement a written exposure control plan
  • offer medical exams, including chest X-rays and lung function tests, every three years to workers exposed at or above the action level for 30 or more days per year
  • train workers on operations that result in silica exposure and ways to limit it
  • keep records of exposure measurements, objective data and medical exams

The construction standard differs in places. For example, it offers medical exams to workers required to wear a respirator for 30 or more days per year.

What the hazard alert lists for controlling dust

The alert follows the hierarchy of controls, which it ranks from most to least effective: elimination, substitution, engineering controls, administrative controls and personal protective equipment. Here are some of its examples, in brief. The full alert has the rest and the detail.

  • Stone choice: verify silica content, and where possible choose products with little or none, without creating a greater or new hazard.
  • Water: replace dry grinders with wet-edge milling machines or stone routers, and modify handheld grinders and polishers to wet the point of contact effectively.
  • Remote tools: use remote-controlled tools with water spray, such as large bridge saws, waterjets and CNC machines, as much as possible.
  • Ventilation: install local exhaust ventilation (LEV) at fixed locations, designed so the airflow doesn't interfere with the water.
  • Isolation: use dust control booths or enclosures with LEV for high-exposure tasks.
  • Housekeeping: "Do not dry sweep or use compressed air to clean floors and work surfaces." The alert points to wet sweeping or wet floor scrubbers. The standard has its own wording and exceptions on both.
  • Water quality: where feasible, use tap water for handheld tools, and limit recycled water to remotely operated machines.
  • Installation: "Do as much work as possible under controlled shop conditions instead of at an installation site." Where onsite finishing can't be avoided, work outdoors and use water to suppress dust.
  • Respirators: the standards require them when other controls alone can't reduce exposures to the PEL, along with a respiratory protection program under 29 CFR 1910.134. That program must include respirator selection, fit testing, medical evaluations and training.

Is wet cutting enough?

Not automatically, going by the alert's data:

  • Sawyers using wet methods: in 22 results OSHA reviewed in 2015, 12 exceeded 50 µg/m³.
  • Adding controls: in one operation with wet sawing, exposures were 70 to 110 µg/m³. Spraying the stone before cutting brought them below 50, and adding LEV brought them to 15 to 32.
  • Handheld grinders: in a NIOSH evaluation, workers using diamond cup wheels with a traditional water spray averaged 121 µg/m³ over a full shift. A follow-up that added sheet wetting from a water hose averaged 33 µg/m³, measured with short-term task-based sampling, so the two figures aren't a like-for-like comparison.

Those are specific sites and studies, not a promise of what a shop would measure. OSHA's standards call for an exposure assessment, and the alert says employers should consult a trained occupational safety and health professional, such as a certified industrial hygienist.

What OSHA's inspections found

OSHA's hazard analysis reports on OSHA's inspections:

  • 2022 data: in workplaces working with natural and engineered stone slabs, approximately one quarter of breathing zone samples exceeded the PEL.
  • Inspection initiative: OSHA launched a focused initiative on engineered stone fabrication and installation on September 22, 2023. Between then and July 8, 2024, it conducted 160 programmed inspections of cut stone and stone product companies and 44 of brick, stone and related wholesalers, plus 42 unprogrammed inspections in these industries. Violations were issued in 149 of them.
  • Common violations: the most common was failure to develop and implement a written hazard communication program. Others in the top five were written respiratory protection program failures and missing medical exams for employees wearing respirators.

Where to get help

  • Small businesses: the alert says they "may contact OSHA's free On-site Consultation Program for assistance" with exposure assessment (OSHA consultation).
  • Written guides: OSHA publishes Small Entity Compliance Guides for general industry and construction.
  • Questions on the standard: see OSHA's silica FAQs.
  • Worried about your health or a coworker's? OSHA's hazard analysis says to contact your local OSHA office.

Why this is on our site

Countertop Visualizer is a sales tool for fabricators, showrooms and stone distributors. It shows slabs on a photo of a buyer's kitchen. It has nothing to do with dust control and doesn't make any shop safer or more compliant. We wrote this page because silica is a serious risk for the people who cut and install the stone our customers sell, and OSHA's own pages are the place to send them.

FAQ

Does OSHA's silica standard apply to countertop shops?

Yes. OSHA's hazard alert says employers whose employees manufacture, finish or install countertops containing crystalline silica must comply with the applicable standard: 29 CFR 1910.1053 for general industry or 29 CFR 1926.1153 for construction.

What is OSHA's exposure limit for respirable crystalline silica?

The permissible exposure limit is 50 micrograms per cubic meter of air, averaged over an 8-hour day. The action level is 25 micrograms per cubic meter, also averaged over an 8-hour day.

Does natural stone contain silica too?

Many natural stones do. OSHA's hazard alert lists typical crystalline silica content of 95% or more for quartzite, 10 to 50% for granite, and under 5% for marble and limestone. Engineered stone ranges from under 0.2% to 95%. Content varies by product, and the alert points to safety data sheets to check it.

Is wet cutting enough to stay under OSHA's limit?

Not always. In OSHA's review of 22 sawyer exposure results where wet methods were used, 12 were above 50 micrograms per cubic meter. The alert describes lower results when water was combined with other controls, such as local exhaust ventilation.

Can a countertop shop use the construction standard's Table 1?

OSHA's general industry standard allows that only for a task that is indistinguishable from a Table 1 construction task and won't be performed regularly in the same environment and conditions. OSHA describes citing a marble and granite company that had wrongly relied on the construction table for work in its shop.

Sources checked 2026-11-05, all from OSHA and NIOSH. Standards and guidance can change, so check the current pages. This page isn't legal, medical or compliance advice. OSHA and NIOSH don't endorse Countertop Visualizer, and their mention here doesn't imply any relationship with it.