← Guides

What happens at a countertop template appointment

Short answer: a template appointment is the visit where your fabricator measures the installed cabinets precisely, so the stone can be cut to fit. Before it, the cabinets must be installed and level, and the sink, faucet and cooktop should be on site, or at least their exact models known. A decision maker should be there to answer questions. It often takes about an hour. Afterwards, the stone is cut from the template, and changes become hard and costly.

Fabricators and showrooms can send this page to a buyer before the appointment. Sources were checked on 2026-11-11, and every fabricator has its own checklist, so check theirs first.

Where it fits

  1. Choose the material and the slab (yard checklist).
  2. Install the cabinets.
  3. Template appointment.
  4. Layout and approval, including where the seams go.
  5. Fabrication.
  6. Installation.

NSI's guide describes templating as "typically the first time we're in the customer's home," in one installer's words, and says that "after the template is finished and approved, the stone is cut and fabricated into the countertop" (NSI).

What has to be ready

These come from published checklists. Your fabricator's list is the one that counts.

Cabinets. One large retailer's checklist (Lowe's) says base cabinets "must be permanently and securely installed, including all cabinet hardware," "must be level and plumb," and "cannot be moved or reconfigured once the template is created" (Lowe's).

Sink, faucet and cooktop. NSI says the fabricator needs to know "the exact make and model of sinks, faucets, and appliances going in or against the countertops." Lowe's says "cooktops and faucet sets must be on site," and that an apron or farmhouse sink "must be permanently and securely installed in base cabinet."

Clear counters. Lowe's says "all countertops need to be completely cleared off." If old counters are being replaced, ask your fabricator who removes them, and when.

Outlets, if the backsplash is stone. Lowe's says that if the backsplash will be in the same material as the countertop, "electrical outlet locations must be identified."

Nearby appliances. Know where the range, fridge and any freestanding appliances next to the counters will go.

Decisions to settle before the day

Bring answers, not open questions:

  • Material and color, and the slab if it's natural stone. Lowe's asks for a "definitive decision on the countertop color material type."
  • Edge profile. NSI says the fabricator should also be told about "edge details, backsplashes, and rear wall treatments."
  • Backsplash: none, 4-inch, full height, or tile (slab vs tile).
  • Sink type and position, faucet holes, and any soap dispenser or other holes.
  • Overhangs for seating, and any support brackets.

Who should be there

Lowe's says a decision maker at least 18 years old must be present, someone who can "answer questions asked by the Countertop Installer." In practice, that's whoever can approve where the sink centers, how far an overhang runs, and similar calls on the spot.

What happens during the visit

  • Measuring. The templater measures every run and records the cutouts and edge details. NSI's article describes one installer using digital tools, and another who uses physical templates made from thin wood strips. A trade guide from SlabWise, which sells fabrication software, says the result is either a physical template cut to the shape of the counters or a digital drawing made with a laser tool (SlabWise, updated July 2026).
  • Questions. Expect questions on overhangs, sink reveal, faucet holes, backsplash and edges.
  • Time. NSI says templating takes "about an hour." SlabWise says the visit "usually takes 30 to 90 minutes for a standard kitchen."
  • Cost. Some fabricators include it in the job, and some charge separately. SlabWise says most charge "$75 to $250," and that the fee "is often credited back against your final job total, but not always." Ask your fabricator.

After the template

  • Layout. For natural stone, the template is matched to the slab. One installer in NSI's article says, "We lay it on the slab and look for inclusions and veining." Ask to see the layout and approve the seams.
  • Fabrication and install. NSI's article says the stone is then cut and fabricated, and an install date is set. Ask your fabricator for their own timeline.
  • Don't move anything. Changes to cabinets, sink or cooktop after templating can mean a new template.

A checklist for the buyer

  • Cabinets installed, level and secured
  • Sink, faucet and cooktop on site, or exact models sent to the fabricator
  • Farmhouse sink installed in its cabinet, if you have one
  • Counters cleared, and old tops removed if agreed
  • Material, color and slab chosen
  • Edge profile, backsplash and overhangs decided
  • Outlet locations known, if the backsplash is stone
  • A decision maker available for the whole visit

Where Countertop Visualizer fits

Countertop Visualizer is used before this stage, to help a buyer choose the color. It doesn't measure, template or plan layout.

  • The buyer's kitchen: photograph it, tap a slab, and see it on their counters in about 20 seconds.
  • Send the image: download it and attach it to a text or email, or share it from your phone if it allows that. Every image carries a small "AI visualization" label, plus your name if you add it.
  • Price: 7 days free, then $250/month. A card is required at signup.

The picture is close enough to choose from, not to sign off on, so the template and layout still decide the job.

Try the demo

FAQ

What is a countertop template appointment?

It's the visit where the fabricator measures the installed cabinets precisely, either with a digital tool or a physical template, and records the sink and cooktop cutouts and edge details. The stone is cut from that template, so it comes after the cabinets are in and before fabrication.

Do the cabinets have to be installed before templating?

Yes, in the checklists we found. Lowe's says base cabinets must be permanently and securely installed, level and plumb, and can't be moved once the template is created. Check your own fabricator's list.

Does the sink need to be there for the template?

Usually yes, along with the faucet and cooktop, or at least their exact make and model. The Natural Stone Institute says the fabricator needs to know the exact make and model of sinks, faucets and appliances going in or against the counters. A farmhouse sink is often installed in the cabinet before templating.

How long does a template appointment take?

Often an hour or so for a standard kitchen. The Natural Stone Institute says about an hour, and one trade guide says 30 to 90 minutes. Larger or more complex kitchens can take longer.

Can I change things after the template?

Changes get hard or costly once the template is made. Lowe's checklist says the sink, cooktop and faucet locations, and the cabinets, can't be changed or moved after templating. Settle the details before the appointment.

Sources checked 2026-11-11. Checklists, fees and timelines vary by fabricator. Product and company names belong to their owners. Their mention here doesn't imply any relationship with Countertop Visualizer.