← Guides

How to pick your slab at the stone yard: a buyer checklist

Short answer: for natural stone, choose the actual slab, not a sample. Bring a cabinet door or paint sample and a photo of your kitchen. Look at the whole slab and then up close, with a flashlight held low across the surface and at the back of the slab. Ask whether it has been repaired or filled. Then have the yard tag it, photograph the tag, and let your fabricator confirm how many slabs you need.

Fabricators, showrooms and yards can send this page to a buyer before a yard visit. Sources were checked on 2026-11-11.

Why the slab, not the sample

The Natural Stone Institute (NSI) advises buyers to "visit stone yards to look at the actual slabs you're going to use, rather than selecting from a sample," because the slab shows "the color, veining, and movement that appears throughout the slab" (NSI). It also says that "each slab of natural stone is different."

Engineered quartz is made to a design, so a sample tells you more. For veined quartz, it's still worth seeing a full slab or the maker's full-slab image (quartz guide).

Before you go

  • Narrow the list. Arrive with two or three colors in mind, not twenty. A salesperson can try options on a photo of your kitchen first (below).
  • Bring samples of the rest of the kitchen. NSI says that "taking samples of other parts of your project" can help narrow the selection. A cabinet door, a paint chip, a floor tile or the backsplash tile all help.
  • Bring a photo of your kitchen and a rough layout or measurements, so the yard can say whether one slab is likely to be enough. Your fabricator confirms that later.
  • Bring a flashlight and your phone. You'll use them both.
  • Ask your fabricator which yards to visit, and whether they want to come or to see photos.

At the yard: the checklist

1. Look at it whole, from a distance

Stand back far enough to see the whole slab. That's closer to how you'll see the counters across the kitchen. Ask yourself:

  • Do you like the overall color, and the movement of the veins across the slab?
  • Is there a part you love, or a part you don't? NSI says you "should work with the fabricator in determining the best part of the slab to use in the most visible areas" (NSI).
  • Does the island or a long run need more than one slab? If so, ask to see the slabs side by side.

2. Hold your samples against it

Put the cabinet door or paint sample against the slab. Yard lighting differs from your kitchen's, so if you can, also take a small piece of the stone home, or photograph the slab in daylight near a door.

3. Look up close, with a flashlight

A trade guide from SlabWise, which sells fabrication software, suggests holding a flashlight "nearly parallel to the stone surface, 2 to 4 inches away" and sweeping it slowly across the face. It advises inspecting dry first, since "water, condensation, or yard dust can obscure fissures or create false readings" (SlabWise, updated July 2026).

4. Know fissures from cracks

  • Fissures are natural features that formed with the stone. Many granites and quartzites have them.
  • Cracks are, in SlabWise's words, "damage that happened after the stone solidified."
  • Not sure? SlabWise suggests placing both hands flat on either side of the line and pushing gently, and treats any movement as a structural concern. Ask the yard's permission first, and ask your fabricator to look at anything you're unsure about.

NSI notes that a fabricator may place part of the slab "in a less prominent section, perhaps because of natural pits or fissures."

5. Ask about repairs and resin

SlabWise says "yards routinely fill open fissures with clear or color-matched epoxy resin before slabs go to display." Resin isn't a bad sign on its own. Ask:

  • "Has this slab been repaired or filled anywhere?"
  • Can I see the back? SlabWise suggests inspecting the back face the same way, and says fissures visible on both faces are "through-fissures."

6. Check it's what it says it is

If the slab is sold as quartzite, check it really is, because some stones sold under that name are softer, acid-sensitive stones. NSI describes simple hardness and acid tests (NSI) and says: "If you don't already own the slab, make sure you get permission before doing this!" See our guide to the tests.

7. Write it all down

Photograph the slab, the tag and any marks you noticed. Note the name, the slab or lot number, the thickness and the finish.

Holding the slab you pick

  • Ask the yard to tag or hold it, and ask how long the hold lasts.
  • Give the slab number to your fabricator, so the slab you saw is the one that's cut.
  • Ask about policies for holds, deposits and returns before you commit.
  • Let your fabricator confirm the quantity. The layout decides how many slabs you need and where the seams go. After that comes the template appointment.

Questions to ask at the yard

  • Is this slab available, and can you hold it? For how long?
  • Has it been repaired or filled anywhere?
  • Can I see the back, and the other slabs from the same lot?
  • What's the thickness and finish? Are other finishes available?
  • Is there enough for my kitchen, or do I need two slabs from the same lot?
  • How do I pass the slab number to my fabricator?

Getting there with a shortlist

Arriving at the yard with two or three colors in mind makes the visit faster and easier. That's where Countertop Visualizer fits for fabricators, showrooms and stone distributors:

  • Your catalog: paste your website URL, and the tool pulls in your logo, colors and slab catalog, and you confirm them.
  • The buyer's kitchen: photograph it, tap a slab, and see it on their counters in about 20 seconds. Then tap the next one.
  • Send the image: download it and attach it to a text or email, or share it from your phone if it allows that. Every image carries a small "AI visualization" label, plus your name if you add it.
  • Price: 7 days free, then $250/month. A card is required at signup.

The picture is close enough to choose from, not to sign off on. It shows a slab photo from your catalog, not the exact slab in the yard, so for natural stone the yard visit is still the final check. It doesn't plan seams or layout, and it doesn't measure anything.

Try the demo

FAQ

Do I need to see the actual slab, or is a sample enough?

For natural stone, see the slab. The Natural Stone Institute advises visiting stone yards to look at the actual slabs you're going to use, rather than selecting from a sample, because each slab is different. A sample shows the color, but not the veining and movement across the whole piece.

What should I bring to the stone yard?

A cabinet door or paint sample, a photo of your kitchen, your rough layout or measurements, a flashlight, and your phone to photograph the slab and its tag. The Natural Stone Institute suggests bringing samples of other parts of the project to help narrow the choice.

Is a fissure in a granite slab a problem?

Usually not. A fissure is a natural feature that formed with the stone, while a crack is damage that happened later. One trade guide suggests pressing gently on either side of a fissure: any movement is a concern. If you're unsure, ask the yard and your fabricator to look at it with you.

Is resin on a slab a bad sign?

Not by itself. Yards routinely fill open fissures with clear or color-matched resin. Ask whether the slab has been repaired or filled, and where, and look at the back of the slab too.

How do I make sure I get the slab I picked?

Ask the yard to tag or hold it, photograph the tag and slab number, and give that number to your fabricator. Ask how long the hold lasts, and have your fabricator confirm how many slabs the layout needs before anything is reserved or cut.

Sources checked 2026-11-11. Yard practices vary, so ask your yard and fabricator. Product and company names belong to their owners. Their mention here doesn't imply any relationship with Countertop Visualizer.